Difference between revisions of "Intro to Soldering"

From MidsouthMakers - Memphis Area Hackerpace
Jump to navigation Jump to search
(adding additional sections to expand in the future)
 
(4 intermediate revisions by the same user not shown)
Line 1: Line 1:
 +
{{ambox |type=content |text = This workshop is being '''redone''' with the addition of an option precursor workshop.  Look for changes in the near future. }}
 +
 
{{Infobox workshop
 
{{Infobox workshop
 
|workshop_name = Intro to Soldering
 
|workshop_name = Intro to Soldering
Line 5: Line 7:
 
|alt =  
 
|alt =  
 
|caption =  
 
|caption =  
−
|start_date = {{date|2010-05-14|mdy}}
+
|start_date =  
−
|end_date = {{date|2010-05-14|mdy}}
+
|end_date =  
−
|cost = $5 to buy a kit<br>$5 to buy a soldering iron (optional)
+
|cost =  
−
|taught_by = Jwoodjr
+
|taught_by =  
 
|website =  
 
|website =  
 
|location = CBU
 
|location = CBU
Line 20: Line 22:
  
 
== Overview ==
 
== Overview ==
−
The purpose of this workshop is entirely to get people introduced to soldering.  It allows them an opportunity to learn which end of the [[soldering iron]] is hot, the proper way to melt and apply the solder, and a chance to assemble a small circuit and see that it does not run on smoke and mirrors. The current workshop assembles a very small circuit composed of a [[555 Timer]] that triggers a LED to remain high for 4.7 seconds.
+
The purpose of this workshop is to educate individuals on how to solder by means of soldering together a predesignated circuit.  This does not include the wiring of the circuit, but merely the soldering of the components into a board with the circuit already etched onto it.
 +
 
 +
== Components ==
 +
<!-- {{bom-start}}
 +
{{bom-row
 +
| item = [http://www.mouser.com/ProductDetail/Tyco-Electronics-AMP/1-390261-9/?qs=sGAEpiMZZMs/Sh/kjph1tvt1/mEPT/Xo7eKgqaeaqYE%3d Component Socket]
 +
| metric = 28 Pin
 +
| cost = 0.30
 +
| quantity = 1
 +
| distributor = Mouser
 +
}}
 +
{{bom-row
 +
| item = [http://www.mouser.com/ProductDetail/Vishay-Dale/XT9S20ANA16M/?qs=sGAEpiMZZMsBj6bBr9Q9abjqaEWBlGuNYHr0DoSKV8w%3d Crystal Oscillator]
 +
| metric = 16 MHz
 +
| cost = 0.55
 +
| quantity = 1
 +
| distributor = Mouser
 +
}}
 +
{{bom-row
 +
| item = [http://mouser.com/Search/ProductDetail.aspx?R=MF1/4LCT52R102Gvirtualkey66000000virtualkey660-MF1/4LCT52R102G Resistor]
 +
| metric = 1 KOhm 1/4 Watt
 +
| cost = 0.05
 +
| quantity = 1
 +
| distributor = Mouser
 +
}}
 +
{{bom-row
 +
| item = [http://www.mouser.com/Search/ProductDetail.aspx?R=PTS645SL70_LFSvirtualkey61170000virtualkey611-PTS645SL70LFS Switch]
 +
| metric = Momentary Push Switch
 +
| cost = 0.13
 +
| quantity = 1
 +
| distributor = Mouser
 +
}}
 +
{{bom-row
 +
| item = [http://mouser.com/Search/ProductDetail.aspx?R=LM7805ACTvirtualkey51210000virtualkey512-LM7805ACT LM7805]
 +
| metric = 5V Regulator
 +
| cost = 0.35
 +
| quantity = 1
 +
| distributor = Mouser
 +
}}
 +
{{bom-row
 +
| item = [http://www.mouser.com/Search/ProductDetail.aspx?R=140-50N2-220J-TB-RCvirtualkey21980000virtualkey140-50N2-220J-TB-RC Ceramic Disk Capacitor]
 +
| metric = 22 pF
 +
| cost = 0.06
 +
| quantity = 2
 +
| distributor = Mouser
 +
}}
 +
{{bom-row
 +
| item = [http://mouser.com/Search/ProductDetail.aspx?R=140-50Z5-103M-RCvirtualkey21980000virtualkey140-50Z5-103M-RC Ceramic Disk Capacitor]
 +
| metric = 0.01 uF or 10 nF
 +
| cost = 0.10
 +
| quantity = 1
 +
| distributor = Mouser
 +
}}
 +
{{bom-row
 +
| item = [http://mouser.com/Search/ProductDetail.aspx?R=UVR1H220MDD1TAvirtualkey64700000virtualkey647-UVR1H220MDD1TA Electrolytic Capacitor]
 +
| metric = 22 uF
 +
| cost = 0.02
 +
| quantity = 1
 +
| distributor = Mouser
 +
}}
 +
{{bom-row
 +
| item = [http://mouser.com/ProductDetail/Atmel/ATMEGA328P-PU/?qs=K8BHR703ZXguOQv3sKbWcg%3d%3d ATMega328 Microcontroler]
 +
| metric = 28Pin (Unbootloaded)
 +
| cost = 4.28
 +
| quantity = 1
 +
| distributor = Mouser
 +
}}
 +
{{bom-row
 +
| item = [http://www.mouser.com/ProductDetail/Murata/RPEF51H104Z2K1A03B/?qs=sGAEpiMZZMuAYrNc52CMZKct9tSo57EF9n5ZqqktZFU%3d Multi Layer Ceramic Capacitor]
 +
| metric = 0.1 uF
 +
| cost = 0.07
 +
| quantity = 1
 +
| distributor = Mouser
 +
}}
 +
{{bom-row
 +
| item = [http://www.mouser.com/ProductDetail/Switchcraft/RAPC722X/?qs=sGAEpiMZZMsUzhEcHltCuRYlx0yK05hp DC Power Connector]
 +
| metric = 2.1 mm (Female)
 +
| cost = 1.29
 +
| quantity = 1
 +
| distributor = Mouser
 +
}}
 +
{{bom-row
 +
| item = [http://search.digikey.com/scripts/DkSearch/dksus.dll?vendor=0&keywords=S7006-ND Female Header]
 +
| metric = 1x8 Pin
 +
| cost = 0.7
 +
| quantity = 2
 +
| distributor = DigiKey
 +
}}
 +
{{bom-row
 +
| item = [http://search.digikey.com/scripts/DkSearch/dksus.dll?vendor=0&keywords=PPTC061LFBN-RC Female Header]
 +
| metric = 1x6 Pin
 +
| cost = 0.56
 +
| quantity = 1
 +
| distributor = DigiKey
 +
}}
 +
{{bom-row
 +
| item = Male Header
 +
| metric = 1x6 Pin
 +
| cost = 0
 +
| quantity = 1
 +
| distributor =
 +
}}
 +
{{bom-row
 +
| item = Male Header
 +
| metric = 2x3 Pin
 +
| cost = 0
 +
| quantity = 1
 +
| distributor =
 +
}}
 +
{{bom-end}}
 +
'''Total: ''' ${{format price| 8.52}} -->
  
 
== Tools ==
 
== Tools ==
−
{{Expand section}}
+
{{expand section}}
  
 
== Instructions ==
 
== Instructions ==
−
{{Expand section}}
+
{{expand section}}
−
 
 
−
== The Circuit ==
 
−
[[Image:One Shot Triggering LED Schematic.png|left|400px]]
 
−
The circuit pictured is called a Monostable Multivibrator configured as a One Shot.  It is commonly used in a fashion known as switch debouncing.  In this particular circuit it is making use of the 5 volt output of the 555 Timer to power the LED for 4.7 seconds.  The circuit can be split into 5 different sections for simplicity of explanation.
 
−
 
 
−
<div style="clear:both;"></div>
 
−
=== Vs ===
 
−
This is simply the power for the whole circuit.  In this particular workshop, the power is two LiPo CR2032 coin cell batteries that are put together and wires coming off for the positive and negative.  Each CR2032 battery outputs 3 volts, and since they are connected in series with one other, providing a total of 6 volts to the whole circuit.
 
−
 
 
−
=== R1 & S1 ===
 
−
R1 is a 10k ohm resistor that is used as a pull down resistor together with the switch so that when the switch is pressed, the trigger pin on the 555 timer goes low.  Once that trigger pin goes low, the 555 Timer's output will remain high for the duration of its cycle.
 
  
−
=== R2 & C1 ===
+
== Circuit ==
−
R2 and C1 together are the determining factor in how long the 555 Timer's output remains high.  The formula used to determine the length of the duty cycle is T = ln(3)*R2*C1 or T ~ 1.1*R2*C1.  In this particular case that is 1.1(91000 ohms)(.000047 farads) = 4.7 seconds.
+
{{expand section}}
  
−
=== 555 Timer ===
+
== References ==
−
The interesting and useful thing about a 555 Timer is that its output is has very sharp edges and is either high (5 volts) or low (0 volts).  This is particularly ideal for computers and other electronics because you don't have a gradual change from one state to another, it is very clean cut and straight forward.  That's how the computer get's its notion of 0's and 1's, but if the voltage lingers somewhere in betweeen, it isn't able to distinguish if it is either a 1 or a 0.
 
  
−
=== R3 & LED1 ===
+
* [http://www.instructables.com/id/Single-Sided-Really-Bare-Bones-Board-Arduino-in-EA/ Really Bare Bones Arduino]
−
R3 is here to simply service the LED, and the LED is here to provide a means of telling when the 555 Timer's output is high. The way this works is you have 5 volts coming out from the 555 Timer, and an LED work on roughly 3.4 volts. If the 5 volts were to travel across the LED, it would simply burn it out because there is too much current going through it. So we reduce the voltage across the LED and therefore reduce the current through it. The easiest way to do this is via a resistor. The way we calculate that is by taking the 5 volts out and subtracting the 3.4 volts that the LED can handle, leaving us with 1.6 volts that we have to get rid of. We also know from the specs of the LED that it pulls roughly 20 milliamps, so using Ohm's Law (V = I * R), we can say that the value of the resistor needed is (1.6 volts)/(0.02 amps) = 80 ohms.  This rounded to the nearest regular resistor value would be 82 ohms.
+
* [http://www.precisebits.com/products/carbidebits/fcrouter.asp Milling Bit] - RCC08-0315-020F
 +
* [http://www.precisebits.com/products/carbidebits/scoreengrave.asp Etching Bit] - EM2E8-0625-45V
 +
* [http://www.precisebits.com/products/carbidebits/drills.asp?tsPT=metric&tsPC=9 Drilling Bit] - DC208-M095-040D

Latest revision as of 05:24, 29 December 2010

 This workshop is being redone with the addition of an option precursor workshop. Look for changes in the near future.
This workshop has an archive of past instructions. If you wish to view the contents of those workshops, please look there.
Intro to Soldering
Information
Location CBU


Overview

The purpose of this workshop is to educate individuals on how to solder by means of soldering together a predesignated circuit. This does not include the wiring of the circuit, but merely the soldering of the components into a board with the circuit already etched onto it.

Components

Tools

Wiki letter w.png This section requires expansion.

Instructions

Wiki letter w.png This section requires expansion.

Circuit

Wiki letter w.png This section requires expansion.

References

Retrieved from "http://wiki.midsouthmakers.org/index.php?title=Intro_to_Soldering&oldid=7730"