Belt Disc Sander: Difference between revisions
updated to not use template redirect and use new template features |
|||
| (6 intermediate revisions by 3 users not shown) | |||
| Line 1: | Line 1: | ||
{{ | {{Infobox tool inventory | ||
|tool_name = | |tool_name = Delta SA446 | ||
|image = | |image = | ||
|image_size = | |image_size = | ||
| Line 7: | Line 7: | ||
|owner = Midsouth Makers | |owner = Midsouth Makers | ||
|category = power | |category = power | ||
|model = | |model = 31-460 | ||
|serial = | |serial = R9025 | ||
|status = available | |status = available | ||
|availability = anyone | |availability = anyone | ||
|talk_to = Ben or Dan | |||
|purchase_date = | |purchase_date = | ||
|disposal_date = | |disposal_date = | ||
| Line 22: | Line 23: | ||
|schedule = | |schedule = | ||
}} | }} | ||
== Location == | == Location == | ||
== Features == | == Features == | ||
*3100 rpm disc and 2000 sfpm belt speed | |||
== Consumables == | == Consumables == | ||
The disc size is 6" and the belt is 4" by 36". If you break or | The disc size is 6" and the belt is 4" by 36". If you break or burn out a belt/disk please replace it. | ||
== Allowable Materials == | == Allowable Materials == | ||
| Line 53: | Line 48: | ||
* Do not wear loose clothing, gloves, neckties or jewelry | * Do not wear loose clothing, gloves, neckties or jewelry | ||
* For dusty operations, wear a dust mask | * For dusty operations, wear a dust mask | ||
== Safe Operation == | |||
*Always sand against a sanding table – no ‘free hand’ sanding in mid-air on the main belt surface | |||
*Always sand pieces significantly larger than the gap between the sanding table and the belt or disc | |||
*Only apply enough pressure to allow the sandpaper to remove material; do not force material into the sander | |||
*Move objects continuously back and forth across the sanding belt or disc to prevent burnout | |||
*Only sand on the left side of the disc; never cross over the center of the disc | |||
*Adjust the table angle by loosening thumb knobs or Allen wrench screws and then moving the tables; make sure to re-tighten and secure the tables before sanding begins | |||
== Prior to each use == | == Prior to each use == | ||
Latest revision as of 14:26, 25 October 2012
| Belt Disc Sander | |
|---|---|
| Information | |
| Owner | Midsouth Makers |
| Tool Category | Tool -> Power Tool |
| Model | 31-460 |
| Serial | R9025 |
| Cost | 0 |
| Status | Available |
| Availability | Anyone may use |
| Labels | |
|
| |
| Media | |
|
| |
| QRCode | |
|
{{#qrcode: http://wiki.midsouthmakers.org/a/Belt_Disc_Sander}} | |
 |
Questions? Talk to Ben or Dan for help or more information. |
Location
Features
- 3100 rpm disc and 2000 sfpm belt speed
Consumables
The disc size is 6" and the belt is 4" by 36". If you break or burn out a belt/disk please replace it.
Allowable Materials
Wood is recommended. Soft plastics and metals can be used but will cause premature belt wear.
Sanded wood must comply with the following rules:
- No moldy or wet wood
- No treated/painted/finished wood
- All nails and staples removed
Personal Protective Equipment
- Wear Safety Goggles
- Use Hearing Protection
- Roll long sleeves above the elbow
- Tie back long hair
- Do not wear loose clothing, gloves, neckties or jewelry
- For dusty operations, wear a dust mask
Safe Operation
- Always sand against a sanding table – no ‘free hand’ sanding in mid-air on the main belt surface
- Always sand pieces significantly larger than the gap between the sanding table and the belt or disc
- Only apply enough pressure to allow the sandpaper to remove material; do not force material into the sander
- Move objects continuously back and forth across the sanding belt or disc to prevent burnout
- Only sand on the left side of the disc; never cross over the center of the disc
- Adjust the table angle by loosening thumb knobs or Allen wrench screws and then moving the tables; make sure to re-tighten and secure the tables before sanding begins
Prior to each use
Hook a vacuum to dust port if sanding a substantial amount. It will make cleanup easier.
After each use
- Brush off any sawdust/leftover materials
- Sweep surrounding area
- Return sander back to its location