View source for Lulzbot AO-101 3D Printer

{{Infobox tool inventory
|image = AO-101-240.jpg
|image_size = 
|alt = MidsouthMakers 3D Printer
|caption = 3D Printer
|owner = Midsouth Makers
|category = cnc
|model = LulzBot AO-101
|serial = VERALE47120240
|status = available
|availability = training
|talk_to = Claudio, Ben, Danny or Cliff
|purchase_date = 05/24/2013
|disposal_date = 
|cost = $0 ($1725)
|dnh = yes
|rtfm = yeshttp://download.lulzbot.com/AO-101/http://www.sherline.com/latheins.htm
|manuals = http://download.lulzbot.com/AO-101/documentation/current/AO-101-User_Manual.pdf
|flickr = 
|youtube = 
|schedule = http://wiki.midsouthmakers.org/a/Tool_scheduling
}}


== Location ==
The LulzBot AO-101 3D Printer is currently on it's dedicated work station in the common room next to the vinyl cutter. Or at least will be after 5/24/2013.

== Features ==
* Usable Print Area: 200mm x 190mm x 100mm (7.9in x 7.5in x 3.9in)
* Top Print Speed: 150mm/sec
* Print Tolerance: 0.2mm (0.008in) in X and Y axes. Z axis is dependent on layer thickness
* Layer Thickness: 0.075mm (0.0029in) to 0.4mm
* Stock filament size: 3mm

== Consumables==
* ABS 3mm plastic filament
* PLA 3mm plastic filament
* Nylon 3mm plastic filament
* Laywoo-D3 plastic filament
* PET print surface on a borosilicate glass bed
*ABS & acetone solution (for ABS first layer adhesion)

===Allowed Filament Vendors===
* [https://www.lulzbot.com/?q=catalog/plastic-filament LulzBot]
* [https://ultimachine.com/catalog/print-materials UltiMachine]
* [http://shop.seemecnc.com/Filament-Plastics_c8.htm SeeMeCNC]

== Recommended Safety Equipment ==
* COMMON SENSE
* Beware of Pinch Points.
* The heated bed gets hot.
* The nozzle gets hot too.

== Prior to each use ==
=== Verify ===
* X and Y belts are taut
* Filament loaded properly 
* Print surface prepped: (PET with ABS solution for ABS printing/Bare glass for PLA/Garolite or cellulose based material for Nylon)
*  Home all axes prior to using the manual movement controls

== After each use ==
=== Clean ===
* Clean bed of any left over filament.
* If using personal filament reload the space filament and prime the nozzle by bringing it to temp and verifying extrusion.
* Home all axes
* Power off the printer using the power switch on the left hand side of the printer (for now)

=== Replace ===
Please leave a donation for any printer use. Filament costs on average $50 a kg (2.2lb) with shipping. Please leave a dollar or two for each hour the print takes. You can donate by giving cash to a board member, with paypal or with purchasing filament. [http://www.midsouthmakers.org/donations/ Make a donation now.] Please purchase reels for ease of use and stability. Coiled filament will work but can be a pain.

==Specs==
{|class="wikitable"
|-
|Board
|Firmware
|Hot end
|Installed nozzle diameter
|Motors
|Belts
|Pulleys
|Extrusions
|Heated Bed
|Glass Bed
|-
|RAMBo v1
|Marlin 1.0
|Budaschnozzle 1.2
|0.5mm
|NEMA 17 
|GT2
|GT2 16 tooth
|Misumi 2020
|Prusa PCB Heater MK1 
|Borosilicate with PET film
|-
|}

===Calibration Standard===
''DO NOT CHANGE/MODIFY/ALTER without checking with Claudio/Orias first.''
{| class="wikitable"
|-
| Motor
| Steps
| Max Length
| Microstep Mode
| Digipot
|-
|X
|50.25
|190
|8
|135
|-
|Y
|50.25
|200
|8
|135
|-
|Z
|756.00
|100
|8
|170
|-
|E0 (Extruder 1)
|408
|NA
|8
|135
|-
|}

===Budaschnozzle specs===

{| class="wikitable"
|-
| Thermistor
| Heater resistor
| Connectors
|-
| 100k Honeywell Thermistor
| 6.8 Ohm
| 
|-
|}

=Slic3r Configurations=
Known good working Slic3r configurations will be stored on [https://github.com/MidsouthMakers/slic3r-configs MidsouthMakers GitHub]

==Usage==
*Navigate to where ever you would like to sync the contents to
* In a terminal window issue the following command: 
 '''git clone https://github.com/MidsouthMakers/slic3r-configs.git'''
* Once synced, run Slic3r and load the desired configuration.

=Usage=
The following services are hosted at [http://192.168.1.10:8080 192.168.1.10] or [http://printer3d.local printer3d.local]
==Repetier-Server==
[http://192.168.1.10:3344/#/printer/A101/control http://192.168.1.10:3344/#/printer/A101/control]Status: Recommended

==OctoPrint==
[http://printer3d.local:5000/ http://printer3d.local:5000/]Status: Working


[http://printer3d.local:8080/?action=stream? OctoPrint webcam stream]Status: Not working

=Authorized Users=
Ben
Cliff
Dan
Joe
Reese
Dru
Claudio
Mark
Andrew
Dan

==Maintenance Performed==
*6/20/2013 Replaced small herringbone gear on extruder stepper motor. Lost one gear tooth after ~13lb of filament.
*6/21/2013 Replaced PET print surface.
*10/24/2013 Haksaw replaced wiring harness and connectors for the hotend.