Lulzbot AO-101 3D Printer

From MidsouthMakers - Memphis Area Hackerpace
Revision as of 03:40, 23 May 2013 by Orias (talk | contribs) (→‎Specs)
Jump to navigation Jump to search
Lulzbot AO-101 3D Printer
MidsouthMakers 3D Printer

3D Printer

Information
Owner Midsouth Makers
Tool Category Tool -> CNC Tool
Model LulzBot AO-101
Serial VERALE47120240
Purchased On 2013-05-24
Cost $0 ($1725)
Status Available
Availability Training required to use
Labels

Read The Freaking Manual.svgDo Not Hack.svg

Media

Link to the manual locationlinks to tool use reservation schedule

QRCode

QR-1066cd9643f34536a154c3edb533d142.png

This tool is to be only used by authorized users. If you wish to learn how to use this tool please contact one of the authorized individuals.
Emblem-question-yellow.svg
 Questions? Talk to Claudio, Ben, Dan or Cliff for help or more information.


Location

The LulzBot AO-101 3D Printer is currently on it's dedicated work station in the common room next to the vinyl cutter. Or at least will be after 5/24/2013.

Features

  • Usable Print Area: 200mm x 190mm x 100mm (7.9in x 7.5in x 3.9in)
  • Top Print Speed: 150mm/sec
  • Print Tolerance: 0.2mm (0.008in) in X and Y axes. Z axis is dependent on layer thickness
  • Layer Thickness: 0.075mm (0.0029in) to 0.4mm
  • Stock filament size: 3mm

Consumables

  • ABS 3mm plastic filament
  • PLA 3mm plastic filament
  • Nylon 3mm plastic filament
  • Laywoo-D3 plastic filament
  • PET print surface on a borosilicate glass bed
  • ABS & acetone solution (for ABS first layer adhesion)

Allowed Filament Vendors

Recommended Safety Equipment

  • COMMON SENSE
  • Beware of Pinch Points.
  • The heated bed gets hot.
  • The nozzle gets hot too.

Prior to each use

Verify

  • X and Y belts are taut
  • Filament loaded properly
  • Print surface prepped: (PET with ABS solution for ABS printing/Bare glass for PLA/Garolite or cellulose based material for Nylon)
  • Home all axes prior to using the manual movement controls

After each use

Clean

  • Clean bed of any left over filament.
  • If using personal filament reload the space filament and prime the nozzle by bringing it to temp and verifying extrusion.
  • Home all axes
  • Power off the printer using the power switch on the left hand side of the printer (for now)

Replace

Please leave a donation for any printer use. Filament costs on average $50 a kg (2.2lb) with shipping. Please leave a dollar or two for each hour the print takes. You can donate by giving cash to a board member, with paypal or with purchasing filament. Make a donation now. Please purchase reels for ease of use and stability. Coiled filament will work but can be a pain.

Specs

Calibration Standard

DO NOT CHANGE/MODIFY/ALTER without checking with Claudio/Orias first.

Board Firmware Hot end Installed nozzle diameter Motors Belts Pulleys Extrusions Heated Bed Glass Bed
RAMBo v1 Marlin 1.0 Budaschnozzle 1.2 0.5mm NEMA 17 GT2 GT2 16 tooth Misumi 2020 Prusa PCB Heater MK1 Borosilicate with PET film
Motor Steps Max Length Microstep Mode Digipot
X 50.25 190 8 135
Y 50.25 200 8 135
Z 756.00 100 8 170
E0 (Extruder 1) 408 NA 8 135

Slic3r Configurations

Known good working Slic3r configurations will be stored on MidsouthMakers GitHub

Usage

  • Navigate to where ever you would like to sync the contents to
  • In a terminal window issue the following command:
git clone https://github.com/MidsouthMakers/slic3r-configs.git
  • Once synced, run Slic3r and load the desired configuration.

Usage

Repetier-server

[192.168.1.XXX]

OctoPrint

[192.168.1.XXX]

Retrieved from "http://wiki.midsouthmakers.org/index.php?title=Lulzbot_AO-101_3D_Printer&oldid=10393"